ANYSHOP e2 Basic Setup Video (English)

CAUTION

Turn off POS terminal and peripheral devices.
Disconnect power cable before starting installation.

How to Connect a Cash Drawer and A10M Printer to ANYSHOP e2.
ANYSHOP e2 Terminal , Cash Drawer, A10M Printer

Tilt the main display upward.
Lift up the I/O port cover.
4-Pin Power Cable
Caution: After installation, please pull out the cab, not the cable.

Connect the power cable to the power port.
Connect the printer cable to the COM3 port.
Connect the printer cable to the printer interface.
Connect the cash drawer cable to the cash drawer port.
Connect the adapter cable to power port.

ANYSHOP e2 MSR Video (English)

CAUTION

Turn off POS terminal and peripheral devices. Disconnect power cable before starting installation.

How to connect a MSR Module to ANYSHOP e2 terminal.
ANYSHOP e2 Terminal, Optional MSR Module, 2 Hand-screws

Attach the MSR module to the main display and fasten them with 2 hand screws.
Place the MSR cable into the groove behind the main display.
Lift up the main display and connect the MSR cable to the I/O port.

POS(Point-of-sale) Terminal BLUO basic Setup Video (English)

POS(Point-of-sale) Terminal BLUO msr Setup Video (English)

POS(Point-of-sale) Terminal BLUO cdp Setup Video (English)

POS(Point-of-sale) Terminal BLUO Dual Monitor Setup Video

ANYSHOP e2 CDP Video (English)

CAUTION

Turn off POS terminal and peripheral devices. Disconnect power cable before starting installation.

How to connect a CDP to ANYSHOP e2 terminal.
ANYSHOP e2 Terminal, Optional CDP Module, Cable

Tilt the main display upward.
Lift up the I/O port cover and remove the screws.
Press down the back cover and push it slightly.
Mainboard Bracket
Turn the bracket screws with fingers.
Caution: Pull the mainboard bracket upward to separate it.
Connect the CDP cable to the mainboard.
Reinstall the mainboard bracket and fasten it with the screws.
Connnect the cable from the mainboard to the CDP module.
Attach the CDP module to the mainboard bracket and tighten the screw.
Put the back cover back on and tighten the screw.

ANYSHOP e2 DualMonitor Video (English)

CAUTION

Turn off POS terminal and peripheral devices.
Disconnect power cable before starting installation.

How to connect dual monitor to ANYSHOP e2 terminal.
ANYSHOP e2 Terminal
ANYSHOP e2 Terminal, Optional Dual Monitor Module, Hinge Module, Cable, 3 Screws.

Lift up the main display and loosen the hand-screws on the back.
Press side buttons of the monitor cable connector and pull out the cable.
Press down the monitor and lift it up to detach it.
Connect the monitor cables to the dual monitor port.
Attach the hinge to the dual monitor. Be careful not to press cables.
Tighten the screw to fasten the hinge.
Organize the cables.
Tighten the screws to fasten the hinge.
Remove the I/O port cover.
Connect the dual monitor cables to VGA port and COM4 port.

Put the I/O port cover back on the system.
Place the main display on the grooves to install it.
Tighten the hand screws on the back of the main display.
Connect the main display cable.

ANYSHOP e2 DualStorage Video (English)

CAUTION

Turn off POS terminal and peripheral devices.
Disconnect power cable before starting installation.

How to install dual hard disk drive.
ANYSHOP e2 Terminal, Optional Dual Hard Disk Module, Cable

Tilt the main display upward.
Lift up the I/O port cover and remove the screws
Press down the back cover and push it slightly.
Turn the bracket screws with fingers.

Caution: Pull the mainboard bracket upward to separate
Connect the hard disk cables to the mainboard.
Organize cables. Be careful not to press them.
Reinstall the mainboard bracket and fasten it with screws.
Attach the hard disk module to the mainboard bracket.
Tighten the screw.
Place MSR cable into the grooves.
Put the back cover back on and tighten the screw.

ANYSHOP e2 StorageReplacement Video (English)

Caution

Turn off POS terminal and peripheral devices.
Disconnect power cable before starting installation.

How to install side USB port.
ANYSHOP e2 Terminal, Optional USB Module, 2 Screws

Lay the terminal on its side.
Open the I/O port cover.
Place USB module on the side.
Tighten the screws to fasten it.
Connect the USB module cable to the USB port.
Close the I/O port cover.